Maksimizirajte zaštitu svoje optike i povećajte uspjeh svog treninga.

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132033156 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

The OpticGard Scope cover for the Burris® FastFire 3 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full optical protection for your reflex sight. Protects against debris, scratches, spent casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without restricting the use of the firearm. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Includes a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132033231 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

OpticGard Visier Cover for Eotech Eflx Designed in den USA: Vollwertiger Optikschutz für Ihr Reflexvisier. Schützt vor Splittern, Kratzern, Patronenhülsen und Abnutzung. Stoßhemmend: Die OpticGard Schutzabdeckung ist schockabsorbierend und kann dauerhaft installiert bleiben ohne die Schusswaffennutzung einzuschränken. OpticGard-Schutzabdeckung mit präziser Kontur, die eine passgenaue Montage und vollen Zugriff auf die Bedienelemente ihres Reflexvisiers gewährleistet. Enthält eine Trainingslinse für das unverzichtbare Okklusionstraining. Schnelle, einfache und komplett werkzeuglose Installation/Deinstallation. Main Data EAN: 4055132033170 Warranty: 1 years Customs tariff number: 90139005000 Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

OpticGard Limited Edition Visor Cover + Training Lens for Vortex Defender ST Designed in the USA: Full optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without limiting the use of the firearm. OpticGard protective cover with precise contour that ensures a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, simple, and completely tool-free installation/deinstallation. Main Data Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

OpticGard Visier Cover for Eotech Xps2 Designed in the USA: Full optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without limiting the use of the firearm. OpticGard protective cover with precise contour that ensures a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, simple, and completely tool-free installation/deinstallation. Main Data EAN: 4055132033163 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

OpticGard Visier Cover for Osight SE Designed in the USA: Full optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without limiting the use of the firearm. OpticGard protective cover with precise contour that ensures a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, simple, and completely tool-free installation/deinstallation. Main Data Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

OpticGard Visier Cover for Vortex Defender ST Designed in the USA: Full optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without limiting the use of the firearm. OpticGard protective cover with precise contour that ensures a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, simple, and completely tool-free installation/deinstallation. Main Data Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

Die OpticGard Scope-Abdeckung für das Osight® bietet Schutz gegen umherfliegende Patronenhülsen und Kratzer. Der intelligente Schnitt ermöglicht es, dass die Abdeckung auf die meisten hinteren und Suppressor-Visiere passt. Sie enthält auch eine abnehmbare Trainingslinse, mit der Sie den Rotpunkt auch bei Sonne oder in hellen Bereichen verwenden können. Unsere Scope-Abdeckungen bestehen aus einem Material aus TPU (Thermoplastisches Polyurethan), das Schutz vor Abrieb bietet. Darüber hinaus ermöglicht die schnelle und einfache Installation einen einfachen Zugang zu den Tasten, ohne die Abdeckung zu entfernen. Schließlich sichern die ineinander greifenden Pins die Abdeckung, sodass sie auch bei starkem Rückstoß von Pistolenschlitten nicht abfällt. Sind Sie es leid, Ihre Optik für Okklusionstraining abzukleben? Unsere abnehmbare Trainingslinse ist die moderne Lösung! Hinweis: Wichtige Informationen OpticGard-Abdeckungen sind möglicherweise nicht mit Backup-Visieren kompatibel, die vor der Optik montiert sind. Es wird ausreichend Platz benötigt, damit sich die Abdeckung an der Vorderseite des Optikgehäuses einrasten kann. OpticGard wird die Optik um ca. 0,08 Zoll (2 mm) an den Seiten erweitern. Wenn Sie zusammen mit einem Holster verwenden, stellen Sie bitte sicher, dass ausreichend Platz zwischen dem Holster und der Abdeckung vorhanden ist. Designed in the USA: Full optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without limiting the use of the firearm. OpticGard protective cover with precise contour that ensures a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, simple, and completely tool-free installation/deinstallation. Main Data Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

THIS COVER IS DESIGNED FOR 407C-X2 /507C-X2, IT DOES NOT FIT HOLOSUN 507C-V2/407C-V2. The OpticGard Scope cover for the Holosun® 507C-X2/407C-X2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Key Features: Can be used while using the firearm Offers protection against stray bullet casings and scratches Intelligent cut fits most rear and suppressor sights Includes detachable training lens for use in bright areas Helps with occlusion training Made from TPU material and polycarbonate for abrasion protection Interlocking pins for secure fit, even with heavy recoil NOTE: OPTICGARD COVERS MAY NOT BE COMPATIBLE WITH BACKUP SIGHTS THAT ARE MOUNTED IN FRONT OF THE OPTIC. SUFFICIENT SPACE IS NEEDED FOR THE COVER TO LATCH ONTO THE FRONT OF THE OPTIC HOUSING. NOTE: PLEASE INSTALL DETACHABLE LENS BEFORE COVER. Designed in USA Patent Pending- World's First Scope Protector That Protects Your Optics From Chips Scratches and Scuffs While in Action Maintains Red Dot Visibility Unlike Others Dust Cover Must Be Removed From Red Dot in Order For Use. Shockproof - Opticgard Scope Cover build in the Interlocking Pins Are Shockproof and is Designed to Shield the Optic From Scratches, Scuffs Caused by Regular Use OpticGard Cover with Intelligent Cut to Allow Cover to Fit Most of Rear Sight Includes a training lens for Occlussion training Fast and easy installation with access to buttons Main Data EAN: 4055132027087 Garancija: 1 Godine Customs tariff number: 90139005000 Mehanički parametri Dimenzije: 50x34.29x34.29 mm Materijal: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Težina: 28.35 g Holosun BKA exception: ne Dodaci OpticGard Training Lens for Holosun 507C- X2/407C-X2 Prikladni članci Holosun HS407C-X2 Otvoreni refleksni crveni točkaš + 2MOA Punkt nišan, solarna ćelija, crna, lov, sportsko gađanje, taktički miniOtvoreni refleksni nišan (Mini) s crvenom odbacivanjem odlikuje se 2MOA točkom, učinkovitim solarnim načinom rada s automatskom kontrolom svjetline, velikom lećom i izdržljivim aluminijskim kućištem.… Holosun otvoreni refleksni nišan HE407C-GR-X2, zeleno točka nišan, lov, airsoft, vojska, Elite serija, RMROtvoreni Elite refleksni nišan (Mini) s zelenim prikazom obilježava se svojom točkom od 2 MOA, učinkovitim solarnim načinom rada s automatskom regulacijom svjetline, načinom zaključavanja i robusnim… Holosun HS507C-X2 Otvoreni refleksni crveni točkaš + promjenjivi 2MOA točka, 32MOA kružni nišan sa solarnom ćelijom, crna, lov, sportsko streljaštvo, Softair, taktički miniOva otvorena refleksna vizira sa crvenim retikulumom 2MOA/32MOA karakteristična je po svojoj mogućnosti zamjene retikuluma, efikasnom solarnom načinu rada s automatskom regulacijom svjetline i čvrsto… Holosun otvoreni refleksni nišan HE507C-GR-X2 s promjenjivim nišanom, zeleno točkaški nišan, lov, airsoft, vojska, Elite serija, RMROvaj otvoreni refleksni nišan ELITE (Mini) s zelenim pomičnim vizirima odlikuje se zamjenjivim vizirima, učinkovitim solarnim načinom rada s automatskom regulacijom svjetline, blokirajućim načinom ra… Holosun HS507C-X2 Offenes Reflex Rotpunktvisier + Adapterplatte für CZ Shadow 2 OROtvoreni ciljnik s crvenom točkom ima veličinu cilja 2 MOA/32 MOA, izmjenjive ciljne točke, učinkovitu solarnu funkciju s automatskim podešavanjem svjetline i izdržljivu konstrukciju od aluminija. Iz… Informacije o sigurnosti proizvoda Proizvođač Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Odgovorni ekonomski operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

THIS COVER IS DESIGNED FOR 407C-X2 /507C-X2, IT DOES NOT FIT HOLOSUN 507C-V2/407C-V2. The OpticGard Scope cover for the Holosun® 507C-X2/407C-X2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Key Features: Can be used while using the firearm Offers protection against stray bullet casings and scratches Intelligent cut fits most rear and suppressor sights Includes detachable training lens for use in bright areas Helps with occlusion training Made from TPU material and polycarbonate for abrasion protection Interlocking pins for secure fit, even with heavy recoil NOTE: OPTICGARD COVERS MAY NOT BE COMPATIBLE WITH BACKUP SIGHTS THAT ARE MOUNTED IN FRONT OF THE OPTIC. SUFFICIENT SPACE IS NEEDED FOR THE COVER TO LATCH ONTO THE FRONT OF THE OPTIC HOUSING. NOTE: PLEASE INSTALL DETACHABLE LENS BEFORE COVER. Designed in USA Patent Pending- World's First Scope Protector That Protects Your Optics From Chips Scratches and Scuffs While in Action Maintains Red Dot Visibility Unlike Others Dust Cover Must Be Removed From Red Dot in Order For Use. Shockproof - Opticgard Scope Cover build in the Interlocking Pins Are Shockproof and is Designed to Shield the Optic From Scratches, Scuffs Caused by Regular Use OpticGard Cover with Intelligent Cut to Allow Cover to Fit Most of Rear Sight Includes a training lens for Occlussion training Fast and easy installation with access to buttons Main Data Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x34.29x34.29 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Weight: 28.35 g Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

The OpticGard Scope cover for the Holosun® EPS Carry offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Compatible Models: EPS CARRY Red MRS EPS CARRY Green MRS EPS CARRY Red 6 EPS CARRY Green 6 Key Features: Can be used while using the firearm Offers protection against stray bullet casings and scratches Intelligent cut fits most rear and suppressor sights Includes detachable training lens for use in bright areas Helps with occlusion training Made from TPU material and polycarbonate for abrasion protection Interlocking pins for secure fit, even with heavy recoil NOTE: OPTICGARD COVERS MAY NOT BE COMPATIBLE WITH BACKUP SIGHTS THAT ARE MOUNTED IN FRONT OF THE OPTIC. SUFFICIENT SPACE IS NEEDED FOR THE COVER TO LATCH ONTO THE FRONT OF THE OPTIC HOUSING. Designed in USA Patent Pending- World's First Scope Protector That Protects Your Optics From Chips Scratches and Scuffs While in Action Maintains Red Dot Visibility Unlike Others Dust Cover Must Be Removed From Red Dot in Order For Use. Shockproof - Opticgard Scope Cover build in the Interlocking Pins Are Shockproof and is Designed to Shield the Optic From Scratches, Scuffs Caused by Regular Use OpticGard Cover with Intelligent Cut to Allow Cover to Fit Most of Rear Sight Includes a training lens for Occlussion training Fast and easy installation with access to buttons Delivery Content 1 OpticGard protective cover 1 black training lens 1 training lens in matching design Main Data Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 44.45x33.02x25.4 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Weight: 28.65 g Shop+Web Delivery Content: * 1 OpticGard protective cover 1 black training lens 1 training lens in matching design Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

The OpticGard Scope cover for the Holosun® SCRS offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Suunniteltu Yhdysvalloissa: Täysi zaštita za reflektorski ciljnik. Štiti od gelera, ogrebotina, čahura i habanja. Otpornost na udarce: OpticGard zaštitna kutija ublažava udarce i može biti stalno postavljena bez ograničavanja uporabe vatrenog oružja. OpticGard zaštitni poklopac je precizno dizajniran oblik koji osigurava točno pristajanje i savršen pristup reflektoru ciljniku. Sisältää vježbanu leću za nužnu okluzijsku obuku. Brza, jednostavna i potpuno bez alata instalacija/uklanjanje. Main Data EAN: 4055132032456 Garancija: 1 Godine Customs tariff number: 90139005000 Mehanički parametri Dimenzije: 45x36x42 mm Materijal: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Holosun BKA exception: ne Prikladni članci Holosun SCRS-RD-MRS crvena točka nišan, promjenjiva 2MOA točka, 65MOA kružni nišan, solarna ćelija, crna, Picatinny/Weaver šina, lov, sportsko gađanje, Softair, taktički mikro crvena točka nišanOvaj mikro refleksni nišan s crvenim ciljem odlikuje se zamjenjivim ciljem (samo u ručnom načinu rada), učinkovitim solarim načinom rada s automatskom regulacijom svjetline, povećanjem linije nišanje… Informacije o sigurnosti proizvoda Proizvođač Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Odgovorni ekonomski operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGHSCRS na Amazonu

The OpticGard Scope cover for the Holosun® SCS Carry offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Dizajnirano u SAD-u: potpuna vizualna zaštita za vizir vaše kacige. Štiti od čestica, ogrebotina, propadanja i habanja. Otporno na udarce: OpticGard zaštita je otporna na udarce i može se trajno instalirati bez ograničavanja korištenja vatrenog oružja. Zaštitna navlaka OpticGard precizno je dizajnirana kako bi savršeno pristajala i omogućila potpuni pristup kontrolama vašeg DSLR digitalnog fotoaparata. Sadrži trening remen koji je važan za trening okluzije. Brza i jednostavna instalacija/uklanjanje bez alata. Main Data EAN: 4055132032470 Garancija: 1 Godine Customs tariff number: 90139005000 Mehanički parametri Dimenzije: 42x26x27 mm Materijal: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Holosun BKA exception: ne Prikladni članci Holosun SCS-320-GR Otvoreni refleksni crveni točkaš + zamjenjivi 2MOA točka, 32MOA krug retikul solarna ćelija, crna, lov, sportsko gađanje Softair, taktički miniOtvorena refleksna nišanica SCS-320-GR za Sig Sauer OR P320 i DPP Footprint sučelja s zelenim vizirskim ciljem od 2MOA/32MOA odlikuje se zamjenjivim ciljem, učinkovitim i ponovno punjivim solarnim na… Informacije o sigurnosti proizvoda Proizvođač Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Odgovorni ekonomski operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGHSCSCARRY na Amazonu

The OpticGard Scope Cover for the Holosun® SCS-PDP offers protection against flying shell cases and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a removable training lens, allowing the red dot to be used even in sunlight or bright areas. Our scope covers are made from a TPU (Thermoplastic Polyurethane) material that provides abrasion protection. Furthermore, the quick and easy installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secure the cover, so it doesn't fall off even with heavy recoil from firearms. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard covers may not be compatible with replacement sights mounted in front of the optic. Sufficient space is needed for the cover to latch on the front of the optic housing. OpticGard will enlarge the optic by about 0.08 inches (2 mm) on the sides. If the optic is used with a holster, please ensure there is enough clearance between the holster and the cover attached. Designed in the USA: Full-fledged optic protection for your reflex sight. Protects against shards, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without restricting firearm use. OpticGard protective cover with precise contour that ensures a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy and completely tool-free installation/deinstallation. Main Data Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x27x26 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

The OpticGard Scope cover for the Delta Point Pro offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Key Features: Can be used while using the firearm Offers protection against stray bullet casings and scratches Intelligent cut fits most rear and suppressor sights Includes detachable training lens for use in bright areas Helps with occlusion training Made from TPU material and poly-carbonate for abrasion protection Interlocking pins for secure fit, even with heavy recoil NOTE: OPTICGARD COVER WILL ONLY BE COMPATIBLE WITH METAL FRAME NOTE: OPTICGARD COVERS MAY NOT BE COMPATIBLE WITH BACKUP SIGHTS THAT ARE MOUNTED IN FRONT OF THE OPTIC. SUFFICIENT SPACE IS NEEDED FOR THE COVER TO LATCH ONTO THE FRONT OF THE OPTIC HOUSING. Designed in USA Patent Pending- World's First Scope Protector That Protects Your Optics From Chips Scratches and Scuffs While in Action Maintains Red Dot Visibility Unlike Others Dust Cover Must Be Removed From Red Dot in Order For Use. Shockproof - Opticgard Scope Cover build in the Interlocking Pins Are Shockproof and is Designed to Shield the Optic From Scratches, Scuffs Caused by Regular Use OpticGard Cover with Intelligent Cut to Allow Cover to Fit Most of Rear Sight Includes a training lens for Occlussion training Fast and easy installation with access to buttons Main Data EAN: 4055132033217 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x31.75x34.29 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Weight: 28.65 g Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGLDPP on Amazon

The OpticGard Scope cover for the Sig Sauer® ROMEO1PRO offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Key Features: Can be used while using the firearm Offers protection against stray bullet casings and scratches Intelligent cut fits most rear and suppressor sights Includes detachable training lens for use in bright areas Helps with occlusion training Made from TPU material and poly-carbonate for abrasion protection Interlocking pins for secure fit, even with heavy recoil NOTE: OPTICGARD COVER WILL NOT FIT WHEN ALUMINUM SHROUD MOUNTED Designed in USA Patent Pending- World's First Scope Protector That Protects Your Optics From Chips Scratches and Scuffs While in Action Maintains Red Dot Visibility Unlike Others Dust Cover Must Be Removed From Red Dot in Order For Use. Shockproof - Opticgard Scope Cover build in the Interlocking Pins Are Shockproof and is Designed to Shield the Optic From Scratches, Scuffs Caused by Regular Use OpticGard Cover with Intelligent Cut to Allow Cover to Fit Most of Rear Sight Includes a training lens for Occlussion training Fast and easy installation with access to buttons Main Data EAN: 4055132033118 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50.8x34.29x27.94 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Weight: 28.65 g Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGSR1PRODEG on Amazon

The OpticGard® cover for the Trijicon® RMR HD offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard® Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard® will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Comprehensive optic protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without restricting the use of the firearm. OpticGard protective cover with precise contour that ensures a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Fast, easy, and completely tool-free installation/uninstallation. Main Data EAN: 4055132033187 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 51x32x32 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGTRHD on Amazon

The OpticGard® cover for the Trijicon® RMR HD offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard® Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard® will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Comprehensive optic protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without restricting the use of the firearm. OpticGard protective cover with precise contour that ensures a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Fast, easy, and completely tool-free installation/uninstallation. Delivery Content 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Main Data Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 51x32x32 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Shop+Web Delivery Content: * 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

The OpticGard Scope cover, for the Trijicon® RMR, offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) providing protection against abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Key Features: Can be used while using the firearm Offers protection against stray bullet casings and scratches Intelligent cut fits most rear and suppressor sights Includes detachable training cover for use in bright areas Helps with occlusion training Made from TPU material and polycarbonate for abrasion protection Interlocking pins for secure fit, even with heavy recoil NOTE: OPTICGARD COVERS MAY NOT BE COMPATIBLE WITH BACKUP SIGHTS THAT ARE MOUNTED IN FRONT OF THE OPTIC. SUFFICIENT SPACE IS NEEDED FOR THE COVER TO LATCH ONTO THE FRONT OF THE OPTIC HOUSING. NOTE: OPTICGARD COVERS ONLY WORKS WITH AUTHENTIC TRIJICON PRODUCTS. NOT COMPATIBLE WITH RMR DUAL-ILLUMINATED Designed in USA Patent Pending- World's First Scope Protector That Protects Your Optics From Chips Scratches and Scuffs While in Action Maintains Red Dot Visibility Unlike Others Dust Cover Must Be Removed From Red Dot in Order For Use. Shockproof - Opticgard Scope Cover build in the Interlocking Pins Are Shockproof and is Designed to Shield the Optic From Scratches, Scuffs Caused by Regular Use OpticGard Cover with Intelligent Cut to Allow Cover to Fit Most of Rear Sight Includes a training lens for Occlussion training Fast and easy installation with access to buttons Main Data EAN: 4055132033095 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50.8x31.75x27.94 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Weight: 28.65 g Holosun BKA exception: no Accessesories 2Pcs OpticGard Traning Cover for Trijicon RMR Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

Made from TPU (Thermoplastic Polyurethane), the OpticGard Scope Cover, for the Trijicon® SRO, offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. Not only is it fast and easy to install, the scope cover provides easy access to the buttons without removing the cover itself. The interlocking pins secure the cover in place, even with heavy recoil from handgun slides. In addition, the cover includes a detachable training lens which allows you to maintain red dot visibility even in the sun or bright areas. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Key Features: Can be used while using the firearm Offers protection against stray bullet casings and scratches Intelligent cut fits most rear and suppressor sights Includes detachable training lens for use in bright areas Helps with occlusion training Made from TPU material and polycarbonate for abrasion protection Interlocking pins for secure fit, even with heavy recoil NOTE: OPTICGARD COVERS MAY NOT BE COMPATIBLE WITH BACKUP SIGHTS THAT ARE MOUNTED IN FRONT OF THE OPTIC. SUFFICIENT SPACE IS NEEDED FOR THE COVER TO LATCH ONTO THE FRONT OF THE OPTIC HOUSING. NOTE:OPTICGARD COVERS ONLY WORKS WITH AUTHENTIC TRIJICON PRODUCTS. Designed in USA Patent Pending- World's First Scope Protector That Protects Your Optics From Chips Scratches and Scuffs While in Action Maintains Red Dot Visibility Unlike Others Dust Cover Must Be Removed From Red Dot in Order For Use. Shockproof - Opticgard Scope Cover build in the Interlocking Pins Are Shockproof and is Designed to Shield the Optic From Scratches, Scuffs Caused by Regular Use OpticGard Cover with Intelligent Cut to Allow Cover to Fit Most of Rear Sight Includes a training lens for Occlussion training Fast and easy installation with access to buttons Delivery Content 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Main Data Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 59.69x31.75x34.29 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Weight: 28.65 g Shop+Web Delivery Content: * 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

Made from TPU (Thermoplastic Polyurethane), the OpticGard Scope Cover, for the Trijicon® SRO, offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. Not only is it fast and easy to install, the scope cover provides easy access to the buttons without removing the cover itself. The interlocking pins secure the cover in place, even with heavy recoil from handgun slides. In addition, the cover includes a detachable training lens which allows you to maintain red dot visibility even in the sun or bright areas. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Key Features: Can be used while using the firearm Offers protection against stray bullet casings and scratches Intelligent cut fits most rear and suppressor sights Includes detachable training lens for use in bright areas Helps with occlusion training Made from TPU material and polycarbonate for abrasion protection Interlocking pins for secure fit, even with heavy recoil NOTE: OPTICGARD COVERS MAY NOT BE COMPATIBLE WITH BACKUP SIGHTS THAT ARE MOUNTED IN FRONT OF THE OPTIC. SUFFICIENT SPACE IS NEEDED FOR THE COVER TO LATCH ONTO THE FRONT OF THE OPTIC HOUSING. NOTE:OPTICGARD COVERS ONLY WORKS WITH AUTHENTIC TRIJICON PRODUCTS. Designed in USA Patent Pending- World's First Scope Protector That Protects Your Optics From Chips Scratches and Scuffs While in Action Maintains Red Dot Visibility Unlike Others Dust Cover Must Be Removed From Red Dot in Order For Use. Shockproof - Opticgard Scope Cover build in the Interlocking Pins Are Shockproof and is Designed to Shield the Optic From Scratches, Scuffs Caused by Regular Use OpticGard Cover with Intelligent Cut to Allow Cover to Fit Most of Rear Sight Includes a training lens for Occlussion training Fast and easy installation with access to buttons Main Data EAN: 4055132033224 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 59.69x31.75x34.29 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Weight: 28.65 g Holosun BKA exception: no Accessesories OpticGard Training Lens for Trijicon SRO Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGTS on Amazon

The OpticGard Scope cover for the Vortex® Defender-CCW offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Key Features: Can be used while using the firearm Offers protection against stray bullet casings and scratches Intelligent cut fits most rear and suppressor sights Includes detachable training lens for use in bright areas Helps with occlusion training Made from TPU material and polycarbonate for abrasion protection Interlocking pins for secure fit, even with heavy recoil NOTE: OPTICGARD COVERS MAY NOT BE COMPATIBLE WITH BACKUP SIGHTS THAT ARE MOUNTED IN FRONT OF THE OPTIC. SUFFICIENT SPACE IS NEEDED FOR THE COVER TO LATCH ONTO THE FRONT OF THE OPTIC HOUSING. Designed in USA Patent Pending- World's First Scope Protector That Protects Your Optics From Chips Scratches and Scuffs While in Action Maintains Red Dot Visibility Unlike Others Dust Cover Must Be Removed From Red Dot in Order For Use. Shockproof - Opticgard Scope Cover build in the Interlocking Pins Are Shockproof and is Designed to Shield the Optic From Scratches, Scuffs Caused by Regular Use OpticGard Cover with Intelligent Cut to Allow Cover to Fit Most of Rear Sight Includes a training lens for Occlussion training Fast and easy installation with access to buttons Main Data EAN: 4055132033101 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 39.37x27.94x27.94 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Weight: 28.65 g Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGVDC on Amazon

The OpticGard Scope cover for the Vortex® Defender-CCW offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Key Features: Can be used while using the firearm Offers protection against stray bullet casings and scratches Intelligent cut fits most rear and suppressor sights Includes detachable training lens for use in bright areas Helps with occlusion training Made from TPU material and polycarbonate for abrasion protection Interlocking pins for secure fit, even with heavy recoil NOTE: OPTICGARD COVERS MAY NOT BE COMPATIBLE WITH BACKUP SIGHTS THAT ARE MOUNTED IN FRONT OF THE OPTIC. SUFFICIENT SPACE IS NEEDED FOR THE COVER TO LATCH ONTO THE FRONT OF THE OPTIC HOUSING. Designed in USA Patent Pending- World's First Scope Protector That Protects Your Optics From Chips Scratches and Scuffs While in Action Maintains Red Dot Visibility Unlike Others Dust Cover Must Be Removed From Red Dot in Order For Use. Shockproof - Opticgard Scope Cover build in the Interlocking Pins Are Shockproof and is Designed to Shield the Optic From Scratches, Scuffs Caused by Regular Use OpticGard Cover with Intelligent Cut to Allow Cover to Fit Most of Rear Sight Includes a training lens for Occlussion training Fast and easy installation with access to buttons Delivery Content 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Main Data Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 39.37x27.94x27.94 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Weight: 28.65 g Shop+Web Delivery Content: * 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

The OpticGard Scope cover for the Holosun® SCS MOS offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optic protection for your reflex sight. Protects against shards, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without restricting firearm use. OpticGard protective cover with precise contour that ensures a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy and completely tool-free installation/deinstallation. Delivery Content 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Main Data Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x25x27 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Shop+Web Delivery Content: * 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]