Maximize the protection of your optics and increase your training success.

The FLEXGARD Scope Cover for the Holosun® SCS MOS and VP9 offers protection against flying cartridge cases and scratches. The intelligent design allows the cover to fit most rear and suppressor sights. Rubber protective cover with solar panel cutout compatible with SCS-MOS-GR and SCS-VP9-GR Note: Important Information The covers may not be compatible with replacement sights mounted in front of the optics. Sufficient space is needed for the cover to latch onto the front of the optic housing. The rubber protective cover will increase the optics by about 0.08 inches (2 mm) on the sides. If the optics are used with a holster, please ensure that there is enough clearance between the holster with the cover mounted. FLEXGARD rubber protective cover with solar panel cutout compatible with SCS-MOS-GR and SCS-VP9-GR Designed in the USA: Full optical protection for your reflex sight. Protects against fragments, scratches, shell casings, and wear. Schnelle, einfache und komplett werkzeuglose Installation/Deinstallation. Main Data EAN: 4055132041465 UPC: 688293089010 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x25x27 mm Material: Rubber Housing Color: Black Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

The FLEXGARD scope cover for the Holosun® SCS-PDP offers protection against flying shell casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. The rubber protective cover with solar panel cutout compatible with SCS-PDP Designed in the USA: Fully-featured optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. FLEXGARD rubber protective cover with solar panel cutout compatible with SCS-PDP Schnelle, einfache und komplett werkzeuglose Installation/Deinstallation. Main Data EAN: 4055132041441 UPC: 688293089003 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x27x26 mm Material: Rubber Housing Color: black Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132032678 UPC: 688293030999 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x35.2x31.6 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: Black Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGAACROP-202 on Amazon

Select Housing color

+6

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132033286 UPC: 688293031095 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x35.2x31.6 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: Carbon Fiber Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGAACROP-2DE11 on Amazon

Select Housing color

+6

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Delivery Content 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Main Data EAN: 4055132043438 UPC: 688293088020 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: Carbon Fiber Shop+Web Delivery Content: * 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

Select Housing color

+1

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132032685 UPC: 688293031002 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x35.2x31.6 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: FDE (Flat Dark Earth) Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGAACROP-209 on Amazon

Select Housing color

+6

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132032043 UPC: 688293031101 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x35.2x31.6 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: FDE Camo Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGAACROP-2DEG83 on Amazon

Select Housing color

+6

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Delivery Content 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Main Data EAN: 4055132043278 UPC: 688293087993 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: FDE Camo Shop+Web Delivery Content: * 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

Select Housing color

+1

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132032661 UPC: 688293031026 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x35.2x31.6 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: Gunmetal Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGAACROP-227 on Amazon

Select Housing color

+6

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132032050 UPC: 688293031125 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x35.2x31.6 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: Gunmetal Camo Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGAACROP-2DEG85 on Amazon

Select Housing color

+6

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Delivery Content 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Main Data EAN: 4055132043285 UPC: 688293088013 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: Gunmetal Camo Shop+Web Delivery Content: * 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

Select Housing color

+1

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132032067 UPC: 688293031132 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x35.2x31.6 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: Navy Camo Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGAACROP-2DEG86 on Amazon

Select Housing color

+6

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132032654 UPC: 688293031019 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x35.2x31.6 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: OD Green Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGAACROP-221 on Amazon

Select Housing color

+6

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132032074 UPC: 688293031118 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x35.2x31.6 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: OD Green Camo Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGAACROP-2DEG84 on Amazon

Select Housing color

+6

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Delivery Content 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Main Data EAN: 4055132043421 UPC: 688293088006 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: OD Green Camo Shop+Web Delivery Content: * 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

Select Housing color

+1

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Delivery Content 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Main Data EAN: 4055132043292 UPC: 688293087986 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: Red Camo Shop+Web Delivery Content: * 1 OpticGard Schutzabdeckung 1 schwarze Trainingslinse 1 Trainingslinse im passenden Design Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected]

Select Housing color

+1

The OpticGard Scope cover for the Aimpoint® ACRO P-2 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full-fledged optical protection for your reflex sight. Protects against debris, scratches, shell casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbent and can remain installed permanently without limiting firearm use. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Contains a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132032647 UPC: 688293031071 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50x35.2x31.6 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: White Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGAACROP-201 on Amazon

Select Housing color

+6

The OpticGard Scope cover for the Burris® FastFire 3 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full optical protection for your reflex sight. Protects against debris, scratches, spent casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without restricting the use of the firearm. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Includes a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132031718 UPC: 688293031552 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50.4x29x26.5 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: Black Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGBFF302 on Amazon

Select Housing color

+7

The OpticGard Scope cover for the Burris® FastFire 3 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full optical protection for your reflex sight. Protects against debris, scratches, spent casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without restricting the use of the firearm. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Includes a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132031831 UPC: 688293031606 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50.4x29x26.5 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: Carbon Fiber Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGBFF3DE11 on Amazon

Select Housing color

+7

The OpticGard Scope cover for the Burris® FastFire 3 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full optical protection for your reflex sight. Protects against debris, scratches, spent casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without restricting the use of the firearm. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Includes a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132043056 UPC: 688293084206 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50.4x29x26.5 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: Dark Wood Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGBFF3DEG88 on Amazon

Select Housing color

+7

The OpticGard Scope cover for the Burris® FastFire 3 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full optical protection for your reflex sight. Protects against debris, scratches, spent casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without restricting the use of the firearm. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Includes a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132031725 UPC: 688293031569 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50.4x29x26.5 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: FDE (Flat Dark Earth) Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGBFF309 on Amazon

Select Housing color

+7

The OpticGard Scope cover for the Burris® FastFire 3 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full optical protection for your reflex sight. Protects against debris, scratches, spent casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without restricting the use of the firearm. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Includes a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132031893 UPC: 688293031613 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50.4x29x26.5 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: FDE Camo Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGBFF3DEG83 on Amazon

Select Housing color

+7

The OpticGard Scope cover for the Burris® FastFire 3 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full optical protection for your reflex sight. Protects against debris, scratches, spent casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without restricting the use of the firearm. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Includes a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132031794 UPC: 688293031590 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50.4x29x26.5 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: Gunmetal Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGBFF327 on Amazon

Select Housing color

+7

The OpticGard Scope cover for the Burris® FastFire 3 offers protection against stray bullet casings and scratches. The intelligent cut allows the cover to fit most rear and suppressor sights. It also includes a detachable training lens which will allow you to use the red dot even in the sun or bright areas. Our scope covers are made from a material made from TPU (Thermoplastic Polyurethane) offering protection from abrasion. In addition, the fast and simple installation allows easy access to the buttons without removing the cover. Finally, the interlocking pins secures the cover so it won't fall off even with heavy recoil from handgun slides. Are you tired of taping your optic for occlusion training? Our removable training lens is the modern solution! Note: Important Information OpticGard Covers may not be compatible with backup sights that are mounted in front of the optic. Sufficient space is needed for the cover to latch onto the front of the optic housing. OpticGard will add approximately 0.08 inches (2mm) to the sides of the optic. If using in conjunction with a holster, please make sure there is sufficient spacing between the holster with the cover on. Designed in the USA: Full optical protection for your reflex sight. Protects against debris, scratches, spent casings, and wear. Shock-resistant: The OpticGard protective cover is shock-absorbing and can remain permanently installed without restricting the use of the firearm. OpticGard protective cover with precise contour, ensuring a perfect fit and full access to the controls of your reflex sight. Includes a training lens for essential occlusion training. Quick, easy, and completely tool-free installation/deinstallation. Main Data EAN: 4055132031886 UPC: 688293031637 Warranty: 1 years Customs tariff number: 90139005000 Mechanical Parameters Size: 50.4x29x26.5 mm Material: Thermoplastisches Polyurethane (TPU) & Polycarbonate (PC) Housing Color: Gunmetal Camo Holosun BKA exception: no Product Safety Information Manufacturer Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] Responsible Economic Operator Picotronic GmbH Rudolf-Diesel-Str.2a 56070 Koblenz Deutschland [email protected] OGBFF3DEG85 on Amazon

Select Housing color

+7